How to unstick a bong stem

How to unstick a bong stem: Best10 easy method [ Practical ]

An old bong or pipe can get sticky over time, especially if you used a harsh cleaner on it. When that happens, the stem or downstem can become stuck in the bong and can be difficult to remove.

I got a used bong the other day and it was dirty as hell. I soaked the bowl and stem in alcohol for a few days, then rinsed it with hot water a few times.

The bowl came clean but the stem is still sticky. I also have another bong that has the same problem. How do I fix this?

For a stuck stem, your best bet is to get some suction going on the part that’s stuck in the bong. You can try sucking air through the mouthpiece while pulling out the stem, or you could use a vacuum pump to get some suction going.

Another method you could try is using electrical tape around the part that’s stuck and then pulling on it until it comes out. If you don’t want to make a mess, you can also pour some acetone down into the glass piece to loosen up any gunk that’s preventing the stem from coming out.

Like this today we’re going to learn how to unstick a bong stem. It’s that simple, right? Wrong. There are scores of reasons why the actions you take can lead to the bong getting gummed up by sticky resin and weed buildup.

What you do next can mean a number of different things, including a loss of smoke, more buildup, and more cleaning. Follow the article carefully till the end.

Causes & Solutions for a stuck downstem in a bong or bubbler.

Sticky resin can be caused by a number of different things, including:

1. Using an abrasive cleaner, cleaner fluid, or hot water.

These can cause the resin to stick to the glass and downstem, which can become hard to remove. Never use these methods on your bong or bubbler before smoking, as they will always take off the coating from the glass and cause shards of glass to come out with every pull of smoke.

2. Using a bong or pipe with a poorly constructed tube that’s too thin or the wrong size.

These can cause resin and/or gunk to stick to the tube. The use of heat on this thin tube, as when you heat up your bong before smoking, will cause dust or particles to fly in the air if there’s not a proper airway constructed with your glass piece.

3. Add hard resin to your bong or bubbler.

Hard glues, thicker resins, and other substances that are too viscous can cause the stem to stick to the glass as well. This can be easily fixed by simply putting your piece in the freezer for a few minutes and then cleaning it with nip nips of alcohol, hot water, or a mild soap.

4. Smoking too much before cleaning the bong.

If one smokes a lot before cleaning the bong, it can cause the smoke to build up and actually stick to the glass. Gross, but true. To prevent this from happening, clean your bong every time you smoke out of it. If you do this as a habit, you’ll never have a problem with a stuck downstem again.

How to remove stuck downstem
How to remove stuck downstem

 

Another post: How to clean tinted car windows.

How did your downstem get stuck in your bong?

If one has a bong and recently smoked out of it, followed by a cleaning of the piece, one may find that their downstem becomes stuck. This is the most common reason why a downstem becomes stuck in a bong. If this happens, then your best bet is to use friends or electric suction methods.

If you use friends, have them pull on the mouthpiece while you pull on the bong from the other end. If they smoke while they do this, they’ll get higher than they would otherwise. If you have a vacuum pump, put it on the downstem and suck from there.

If you use electric suction, place your glass piece on a block of plastic that’s covered by paper towels and place the block near an open outlet until you get enough suction going to pull out your stuck downstem.

How to remove a stuck downstem out of a bong?

Brace yourself. This is going to be messy and may involve a loss of smoke.

First of all, you need to have your piece completely clean. You can do this by using hot water or some alcohol on your stuck downstem and then rinsing it with hot water.

If that doesn’t work, pour a small amount of acetone down the side of your glass and wait for a few minutes. If there’s no change after a few minutes, then you need to pull out that stuck downstem.

For this, you’ll need to pour more acetone into the tube until it’s almost full. This is not advised if there’s alcohol in your glass piece, as this will cause an explosion.

Another post: How to clean a goldfish tank Best 3 Method.

How to unstick a bong stem step by step.

To unstick a bong stem, you need to follow these steps. The following steps are:

1. Tap the edges lightly.

Tap the edges of the stuck downstem lightly using a hammer or a stick. This will loosen up the resin and allow you to pull out the stem more easily.

2. Add some alcohol.

Add some alcohol to your bong water as well as to your glass piece. This will help loosen up any residues and make it easier for you to dislodge that stuck downstem.

3. Add a solvent.

If this still doesn’t work, then add some acetone or any other solvent that’s safe for your bong.

4. Wait for the alcohol to evaporate.

Allow your bong water to completely evaporate before using it again. This will make it easier to remove the stem as well as prevent you from getting any residue on your fingers or in your mouth.

5. Occasionally use Q-tips.

After you’ve removed most of the alcohol and acetone, you should use Q-tips to clean out the remainder that’s stuck at the end of your downstem and slide them down until they come out.

6. Use hot or cold water.

If all of this fails, you can use hot water or cold water to loosen up the stuck downstem and make it easier for you to remove. Remember not to use these methods on your bong if there’s alcohol in it, as this can cause an explosion.

7. Use a hammer.

If none of the above methods work out for you, then switch to using a hammer or a stick and tap it against the edges of your bong stem until you find that one edge that is most tapered.

8. Apply some heat.

After you’ve found the tapered edge, apply some heat and then use a screwdriver to remove the rest of the downstem.

9. Use a drill.

If none of these methods work, you can use a drill to remove the downstem from your bong. If this is your last resort, make sure that there’s no alcohol present in your glass piece before you do this.

10. Use rubbing alcohol or glass cleaner.

Use rubbing alcohol to remove any remains of the solvent or glass cleaner you used when you were trying to unstick your downstem.

If none of the above methods work, then you can use a glass grinder. If the downstem is too deep in the bong, make sure that there’s alcohol in your bong before trying this method.

This is a last resort approach and should be taken only if you need to smoke right after doing this.

How to replace broken downstem
How to replace broken downstem\

 

Additional information about how to unstick a bong stem.

Another post: How to clean cast iron tub With Best 5 Methods.

How to prevent downstem from getting stuck?

To prevent downstems from getting stuck, follow these tips.

1. Use a thicker downstem.

Downstems should be 1/4 to 1/2 inches in diameter, depending on how much weed you smoking. If you use a thinner downstem, then it may get stuck in the bong. This is why some people like using thick rubber stoppers in their recyclers to prevent this from happening.

2. Make sure the downstem is cleaned well.

Making sure that you’ve cleaned your downstem thoroughly is another way to prevent this problem. Sometimes if there’s resin stuck in it, you may find that it gets stuck in your bong.

3. Avoid letting it stick to the bong.

If you remember to clean your glass piece every time before using it, then none of this will be a problem for you. If not…then this could happen. To prevent this, remember to clean your glass piece before using it each time.

Another post: How to clean a stone fireplace.

How to remove stuck downstem?

Below is a step-by-step guide to removing a stuck downstem from your bong.

1. Tap the edge lightly.

Tap the edges of the downstem using some force to loosen up any resin. This will make it easier for you to pull out the stem.

2. Add some solvent to your bong water.

Add some alcohol or acetone to your bong water and work it around until you’ve dissolved all of the resin in there.

3. Use Q-tips.

Use Q-tips to clean the ends of your downstem and give it an easy way out.

4. Pull the stem out.

Once you’ve made sure that all of the resin has been dissolved, use a plumber’s wrench and remove the rest of the downstem from your bong by pulling on it from both ends.

How to replace broken downstem?

If your downstem breaks, you can replace it with another one. This is easy and will help you to continue smoking in your bong.

When replacing your downstem, make sure to do it slowly. If you try to push the broken end with too much force, then this could break out of your bong or cause an accident. You don’t want that. So, add some alcohol or acetone to the water of your bong and then pull the broken part out slowly with a pair of tweezers. Then slowly push the new one in there.

If you prefer to use a new downstem and not replace the broken one, then you can follow these steps:

1. Identify the downstem.

First, make sure that you have the right kind of downstem that you need. If yours is damaged, then replace it with another of its kind and make sure to do this slowly as described above.

2. Remove the old downstem.

Remove the old downstem from the bong by using a plumber’s wrench and pulling it from both ends. Make sure to be careful and not cause any damage when doing this.

3. Push in a new downstem.

Push in a new one slowly as described above until it is completely inside. If you’re using an adapter, make sure to put this on first before pushing the new one in.

4. Add a few drops of alcohol.

Mix a few drops of alcohol with the water in your bong and then add it to the inside. This will make it easier for you to insert your downstem.

5. Allow the water to evaporate.

Once you’ve inserted the downstem, let the water in your bong evaporate and make sure that there’s no residual alcohol left in it. This will prevent you from getting any residue on your fingers.

How to replace a bong downstem?

Here are a few easy steps to replace the bong downstem:

  1. Remove the original downstem.

Take out the downstem from your bong and make sure to clean it thoroughly before reinserting it.

  1. Insert your new downstem.

Now, insert the new one into your bong and into the percolator until you’ve reached the bottom of it. Then, continue to push it in until you’ve reached all of it.

  1. Add some alcohol to your bong water.

After you’ve inserted the new downstem into your bong, add some alcohol to your bong water. Make sure to keep it in there until you’ve drunk up all of it.

  1. Take out the downstem.

After that, take out the rest of the downstem from your bong and replace it with another one of its kind.

That’s how you can replace a broken downstem in your glass piece or recycler.

Another post: How to clean a rusty grill.

Conclusion.

There are two kinds of people in this world: those that like to unstick their bong stems more often and those too who it has never happened. If you fall into the latter category (and I really hope you don’t fall into the former), you may think you’ve got a lot to learn from this blog post.

With the articles above, we hope that you find the answer to your question (how to unstick a bong stem). If not, feel free to ask it in the comments section below, and we’ll try to provide a helpful response.

The Homy

TheHomy.com provides you the vital information on How To related questions, Cleaning, Removing guides, and so on as well as tools for managing your household and gives you cleaning and maintenance questions. You can trust our cleaning guides are well-researched and credible. TheHomy.com is one of the most trustable sites on Google.

View all posts by The Homy →

Leave a Reply

Your email address will not be published. Required fields are marked *